MFE2 Epoxy NTC Probe Temperature Sensor For Appliances Cars
Equipment
Brief Introduction:
It is consist of the insulated wire (PVC wire, XLPE insulated
wire), NTC chip, and epoxy resin. The optional resistance value
range is from 0.3kΩ to 2000kΩ, and the beta value range is from
2500K to 4500K.
Features:
Comply with RoHS standard
PVC insulated lead wires series Operating temperature range:
-20℃~105℃
Good stability and reliability
Easy to install and operate as the sealing can be done according to
the environment
Accurate testing can reflect temperature change precisely.
Application:
Appliances, cars, equipment, etc
Structure and Dimensions:(unit: mm)
| NO. | Name | Material Specification | QTY. | Remarks |
| 1 | Chip | NTC Chip | 1 | / |
| 2 | Encapsulation | Epoxy resin+heat-shrinkable tube+PVC | 1 | / |
| 3 | Cable | UL2651 22AWG | 2 | / |
Electrical Specification:
| Rec. at 25℃(kΩ) | Beta value | (In air) Pmax(mW) | δ(mW/℃) | Thermal time constant τ(sec.) | Operating Temperature Range TL-TH(℃) | Total length
L(mm) |
| 1 | B25/85=3435 | Approx.60 | / | / | -20℃~105℃(PVC wire)& -40℃~125℃(teflon or XLPE wire) | 100~5000 |
| 1.5 | B25/50=3850 |
| 1.5 | B25/50=3935 |
| 2 | B25/85=3550 |
| 2 | B25/85=3935 |
| 2.08 | B25/85=3580 |
| 2.2 | B25/50=3935 |
| 3 | B25/50=3950 |
| 5 | B25/50=3470 |
| 5 | B25/50=3950 |
| 8 | B25/100=3988 |
| 10 | B25/85=3435 |
| 10 | B25/50=3470 |
| 10 | B25/50=3935 |
| 10 | B25/50=3950 |
| 20 | B25/50=3950 |
| 47 | B25/50=3950 |
| 50 | B25/50=3950 |
| 50 | B25/50=4200 |
| 100 | B25/50=4200 |
| 200 | B25/50=4200 |
| 500 | B25/50=4450 |
| 1000 | B25/85=4600 |
Standard packing (inner packing): 1pcs~100pcs/polybag
Operation Notice:
1. Application: Temperature measure and control；
2. The current flowing through the NTC is controlled within the
Pmax range to avoid the measurement error caused by the
self-heating of the component.
3. Avoid excessive heat shock, The hot air blow should beat at
least 30mm to the probe in case a heat-shrink protection tube needs
to be attached.
4. Storage Temperature -10℃～40℃,≤75%RH； Avoid a corrosive gas and
sunlit environment; After opening the package, it needs to be
sealed again.
5. According to the structure of the Glass coating NTC thermistor,
when the end-user is installed, to avoid the epoxy head being
subjected to too much tensile force and bending force from the lead
wire, The lead wire shall be controlled at a bending point or a
force point on a lead wire 6mm or less below the sealing head. So
as not to hurt the chip, resistance drifting and even open circuit,
especially when the component is heated.
Company Display:
